返回到 Pressure, Force, Motion, and Humidity Sensors
學生對 科罗拉多大学波德分校 提供的 Pressure, Force, Motion, and Humidity Sensors 的評價和反饋
219 個評分
課程概述
"Pressure, Force, Motion, and Humidity Sensors" can also be taken for academic credit as ECEA 5342, part of CU Boulder’s Master of Science in Electrical Engineering degree.
This is our third course in our specialization on Embedding Sensor and Motors. To get the most out of this course, you should first take our first course entitled Sensors and Sensor Circuits. Our first course gives you a tutorial on how to use the hardware and software development kit we have chosen for the lab exercises. This third course assumes that you already know how to use the kit.
After taking this course, you will be able to:
● Understand how to specify the proper AC or DC motor for a machine design.
● Integrate the motor to a machine, based on analysis of motor equations for voltage, current, torque and speed.
● Implement the motor and accompanying rotary sensor into a motor control circuit in both hardware and software.
● Add a motor and motor control circuit into a microprocessor based development kit.
● Create hardware and firmware to process motor feedback data to a microprocessor for further evaluation.
After taking this course, you will be able to:
● Understand how to specify the proper pressure, force, strain, position, motion, acceleration, occupancy, and humidity sensors for taking real-time process data.
● Implement these sensors into an embedded system in both hardware and software.
● Add the sensor and sensor interface into a microprocessor based development kit.
● Create hardware and firmware to process sensor signals and feed data to a microprocessor for further evaluation.
In this course you will build the circuit from Video 7 (Lab Exercise on strain gauges), Module 2 (Force and Strain Sensors and Touch Screens), and use it to make screen shots of the timing of the switch. If you haven't already wired up the system and written all the software per the instructions of Video 7, please do so now.
You will need to buy the following components to complete this assignment. Note that if you have already purchased the PSOC 5LP PROTOTYPING KIT, you do not need to buy it again.
These parts may be purchased off the Digikey web site, www. Digikey.com. One part needs to be purchased off the Sparkfun website www.sparkfun.com. Or, you may obtain the specs from the site, and purchase them elsewhere.
Digikey Part numbers are typed out here:
428-3390-ND
CF14JT22K0CT-ND
CF14JT100KCT-ND
Table shown here:
Index Quantity Part Number Description
1 1 428-3390-ND PSOC 5LP PROTOTYPING KIT
2 2 CF14JT22K0CT-ND RES 22K OHM 1/4W 5% AXIAL
3 1 CF14JT100KCT-ND RES 100K OHM 1/4W 5% AXIAL
Sparkfun part numbers are typed out here:
TAL221
Table shown here:
Index Quantity Part Number Description
1 1 TAL221 Mini-load cell - 100g, straight bar
Additional equipment needed:
• Wire - various gauges and lengths
• Breadboard
• Oscilloscope – suggested models are:
o PICOSCOPE 2204A-D2 available on www.digikey.com or
o Digilent 410-324 | OpenScope MZ available on www.newark.com
Depending on your budget, you can also investigate these models:
o Hantek HT6022BE20MHz - https://www.amazon.com/dp/B009H4AYII
o SainSmart DSO212 - https://www.amazon.com/dp/B074QBQNB7
o PoScope Mega50 USB - https://www.robotshop.com/en/poscope-mega50-usb-mso-oscilloscope.html
o ADALM2000 - https://www.digikey.com/en/products/detail/analog-devices-inc./ADALM2000/7019661
熱門審閱
BJ
2022年8月14日
Great introduction course to sensors. I really enjoyed the instructors videos as they were clear and engaging. I would recommend it.
TH
2020年8月27日
This course is very interesting. I completed this course.But I can not get my certificate.Please help me to earn my certificate.
篩選依據：
1 - Pressure, Force, Motion, and Humidity Sensors 的 25 個評論（共 48 個）
創建者 JiaJie, X
•2020年7月15日
創建者 Paul P
•2020年4月9日
創建者 Pablo C S
•2019年11月12日
創建者 HET V B
•2020年7月28日
創建者 Amit A
•2020年7月5日
創建者 Vinsensius C F
•2020年5月1日
創建者 Enrique V
•2020年5月29日
創建者 MR. V S
•2020年5月12日
創建者 Abhishek K
•2020年5月10日
創建者 Mr.KAUSTUBH K S
•2020年4月21日
創建者 Bonifasius B S A
•2020年5月16日
創建者 Ngo T D
•2021年3月4日
創建者 Guillaume V
•2020年4月3日
創建者 Brittany j
•2022年8月15日
創建者 Theint Z H
•2020年8月28日
創建者 Kasuntha M
•2020年11月11日
創建者 Sachin G
•2020年11月3日
創建者 Nimisha M
•2020年12月23日
創建者 KARIMULLA S
•2020年8月3日
創建者 Pankaj R
•2022年9月20日
創建者 Ganesh R P
•2020年6月23日
創建者 Neredikomma S R
•2020年6月12日
創建者 Yared B
•2021年1月28日
創建者 Jos� R
•2020年8月2日
創建者 P S K R
•2020年6月12日
Coursera Footer
© 2022 Coursera Inc.保留所有權利。
